Complete custom keyboard (Part 5)
Behold! The completed custom keyboard:
I am very happy to have finished and delivered the completed keyboard. It took over a year.
Posts about making
Mostly complete keyboard (Part 4)
Now the keyboard is pretty much done. For real this time.
Refer to (part 1), (part 2), and (part 3) for the back-story.
I previously wrote that I was "almost done" but in reality I wasn't anywhere near complete. There were many bad solder joints, resulting in shorts and disconnections for many buttons and several shift registers. It was frustrating because I had no idea how to debug it.
Eventually I wrote some Arduino diagnostic code to help me identify the problems. I also read several books on Multimeters. And lots of time studying my soldering joints with a magnifying glass. It was tedious, but now the keyboard works pretty flawlessly. Although it is possible another problem will creep up later, I am confident I will be able to deal with it.
The circuitry is complete. A few minor tweaks to go: some buttons needed to be filed down to fit properly, and perhaps a few more need some work. The keyboard also doesn't have question mark or comma keys. I plan on using a laser cutter to make replacement buttons for the duplicate times and caret characters since they aren't as important. I will take care of it at ITP Camp this summer.
And this is me typing with it! It really works!!
Some photos:
I wrote my own Arduino code to run the Arduino board. My code properly handles multiple key presses and lets the operating system handle key repeats. There is also diagnostic code to blink the Arduino's built-in LED if there is a hardware problem with the shift registers.
I am very happy to have finished the circuitry for this custom keyboard. For a long time this project seemed hopeless. Nevertheless, I stuck with it and now it is clear I will actually finish it properly. The soldering iron that was setup on my kitchen table since August has finally been put away. I'll take it out again later, of course, but for a different project!
Next up, Raspberry Pi experiments.
In memory of my lamp
Tragically, the second lamp I made at ITP camp is gone.
I accidentally toppled it today. It fell, shattering into pieces.
I am not upset though. Most of the parts were salvageable and will be re-used in a future lamp. I have three wine bottles with holes already drilled in them, so I can make an identical lamp if I want to. I won't though. I realize now that filling the bottle to the top with gravel raised the center of gravity higher than where it should be. The next one will will be half filled with gravel. How about plastic or glass beads for the top half? I could make something that looks fishtank-like. I am sad that lamp is gone, but know that the next lamp will be better.
And now is a good time for a public service announcement on the proper way to clean up glass:
Very effective. I had bread-crumbs everywhere but that is much easier to deal with than the broken glass.
Finishing a custom keyboard at home (Part 3)
Almost done with the custom keyboard!
Refer to (part 1) and (part 2) if you have not read them already.
I finally built up the courage to attempt the actual assembly. This part was very difficult and it took me a long time to figure out something that made sense and seemed achievable. There are so many buttons...how am I supposed to organize the buttons, the wires, the shift registers, and the resistors?
I started by soldering the buttons into place in their correct locations on each circuit-board along with resistors and wires for power and ground. Each circuit-board connected the power and ground wires to each other so I only had to add two wires from one board to the next to power the buttons.
Making a custom keyboard at home (Part 2)
I continue to work on the custom computer keyboard (part 1). After creating the laser cut parts, I needed to understand the electronic components. Unfortunately I hadn't done anything with an Arduino in a long time, so I was confused about what needed to be done.
To help me learn, I bought an educational Arduino kit and started working on the experiments. That was definitely worth my while. I got comfortable using an Arduino again. I also learned what shift registers are. There will be 10 of them in this keyboard, as they are essential to allow the Arduino to sense the button presses of 71 buttons.
Here's one of the kit's experiments, using two Serial to Parallel shift registers to control a dot matrix LED display.
Making a custom keyboard at ITP Camp (Part 1)
I spent the month of June at ITP Camp. It's my third summer in a row there, and as always, I had a blast. This year I attended a session on building a custom computer keyboard. It was taught by Claire Kearney-Volpe and Ben Light.
In the class we met with several members of United Cerebral Palsy and discussed their experiences using computer keyboards. Traditional keyboards often do not meet the needs of disabled people. We talked about ways we could re-design a keyboard to make computers more accessible and meet their usability needs.
I worked with a woman named Shaniqua. She didn't like the traditional key arrangement of a QWERTY keyboard and often found it difficult to find the next key she needed to type. There were some keys she didn't use at all and she thought the keys were too close together.
I made another lamp
I made another lamp; this time, out of an empty wine bottle.
Similar design and build as the first one, made with leftover gravel. The lampshade is the same color and fabric, so they're an matching set!
Someday I'll probably make third one and give it away.
I made a lamp
I made a lamp out of an empty olive oil bottle.
After removing the label and cleaning it out, I drilled a hole near the bottom using diamond drill bits and a press drill. The electric cord runs through the center of the bottle up to the opening on top.
The bottle is filled with fish tank gravel. It was very hard getting it in the bottle! I tried using a funnel but it kept getting clogged. Eventually I settled on dumping it in the mouth by hand with the bottle in a large bin to catch the many rock pieces that did not go inside. This took some time.
The mauve lamp shade is made of silk. I think it matches the gravel quite well.
I also made that coaster sitting on the nightstand. That was a long time ago though.
